datasheet for steel grades alloy steel x4crnimo 16
16MnCr5 grade steel is a case hardening steel used extensively for both carburising and carbonitriding, demonstrating reasonably high hardenability and excellent forgeability. This grade also has excellent weldability, however care should be taken to avoid weld cracking. Machinability is approximately 80% of that of mild steel.
Alloy 410 (UNS S41000) is a 12% chromium martensitic stainless steel plate that can be heat treated to obtain a wide range of mechanical properties. The alloy has good corrosion resistance along with high strength and hardness. In the annealed condition, 410 stainless steel plate is ductile and may be formed. B16 Alloy Steel Bar, B-16 bolt material and fastener materialsB16 Alloy Steel Bar - B5F5B - ASTM A 193. B16 alloy steel bar is a chromium, molybdenum, vanadium alloy steel widely used for high strength industrial applications. It is commonly used in power generation turbines in high strength fastener applications such as bolt material.
XLERPLATE® steel Boiler & Pressure Vessel Grades. PT490NRA (L20, L40, L50) TUBEFORM® steel G300 Data Sheet (119 KB) ZINC HI-TEN® G450 and G450S steel Datasheet (192 KB) BlueScope Steel Limited ABN 16 000 011 058 COLD ROLLED - AK SteelHigh Strength Low Alloy Steel (HSLAS-F) Grade 50 50 340 60 410 22 Grade 60 60 410 70 480 16 TABLE 3 SAE SPECIFIED PROPERTIES Quality Designation Description Min. YS Min. UTS n-Value MPa MPa Bake Hardenable 180 SAE J2340 Type 180B 180 300 0.19 Dent Resistant 210 SAE J2340 Type 210A 210 330 0.19 Bake Hardenable 210 SAE J2340 Type 210B 210 320
P460NL2 steel grade is one of grade in En10028-3, which is non alloy and alloy steels with specified elevated temperature properties. P460NL2 grades are used above all for manufacturing boilers, pressure vessels and pipes transporting hot liquids. Gangsteel is specialized in supplying EN10028-2 steel plate in grade P460NL2. GALVANIZED STEEL Grade Data SheetGRADE 40 Mechanical Properties Chemical Composition Steel base Guaranteed Typical Range Guaranteed Maximum Percent Longitudinal tensile Carbon (C) 0.25 Yield strength, minimum ksi 40 40-51 Phosphorus (P) 0.10 Tensile strength, minimum ksi 55 55-63 Manganese (Mn) 1.35 Elongation in 2 inch, minimum % 16 16-37 Sulfur (S) 0.04
Galvanised (zinc coated steel) is available in various steel grades with guidelines on suitable steel substrate for moderate bending/forming, severe bending, moderate drawing and load-bearing applications. Steel chemistry design and thermo-mechanical processing provide different mechanical properties for the substrates tabulated in Table 1. Handbook of Comparative Handbook World Steel vii Handbook of Comparative World Steel Standards Getting Started With This CD-ROM Minimum System Requirements - Intel Pentium processor - Microsoft Windows 98 Second Edition, Millennium Edition, Windows NT 4.0 (SP 6), 2000 (SP 2),
Aug 25, 2009 · Bolts, Steel Grade 36 Low or medium carbon steel 1/4 - 4-in 58,000(min) 80,000 (max) 36,000 ASTM A563 Grade A (hex up to 1-1/2 & Heavy Hex 1-1/2 and over) Notes 1, 2, 3 ASTM F835 Socket Button & Flat Countersunk Head Cap Screw Medium carbon alloy steel:quenched & tempered ASTM A563 Grade DH Heavy Hex SAE J995 Grade 5 up to 1-1/2, ASTM A563 SAE AISI 4340 Steel Properties, Heat Treatment, Equivalent 4340 Alloy Steel Datasheet. The following tables and lists give 4340 alloy steel datasheet and specification including chemical composition, physical properties and mechanical properties, heat treatment, welding, etc. Chemical Composition. AISI 4340 steel material chemical composition is listed in the following table based on cast analysis.
Each stainless steel families regroup different grades, which have different composition leading to different properties. Stainless steel grades alloys content (Mass %) min - max min - max min - max min - max min - max min - max 201 0,15 16,00 - 18,00 3,50 - 5,50 5,50 - 7,50 0,05 - 0,25 Austenitic Stainless Steel Alloy 440 - Continental Steel & Tube CompanyStainless Steel Alloy 440. Type 440 Stainless Steel, as known as razor blade steel, is a hardenable high-carbon chromium steel. When put under heat treatment it attains the highest hardness levels of any grade of stainless steel. Type 440 Stainless Steel, which comes in four different grades, 440A, 440B, 440C, 440F, offers good corrosion
Grade Data Sheet 301 301L 301LN Revised May 2008 Page 1 of 2 atlassteels.au Grade 301 is a high work-hardening rate austenitic stainless steel. It can be supplied with a tensile strength of up to over 1300 MPa in strip and wire forms, to produce tempers in the range of 1/16 Hard to Full Hard. The controlled analysis of Grade 301 enables Stainless Steel Grades and Families - Unified AlloysMost offer good weldability and formability in comparison to other families of steel. Some are offer improved corrosion resistance. Chloride-resistant stainless steels are especially popular in offshore use. Common duplex alloys include are 318L, LDX 2101, LDX 2304, 2507 and 4501 (Also known as 25CR superduplex) grades.
Carbon Steel:A36, A572 GR 50, A588 (Corten type), 1045, A516 GR 70, A514 T-1 Carbon Alloy:4130, 4140, 4340 Abrasion Resistant:AR400, AR500 Other Grades:33Max, A285 GR C, A515 GR 70, ABS Grades, & AR360 Common Size Ranges Thickness Width Length 3/16 8 36 to 120 96 to 480 Can cut to size. Steel Plate Catalog Commercial  Steel Standards - ASTMASTM's steel standards are instrumental in classifying, evaluating, and specifying the material, chemical, mechanical, and metallurgical properties of the different types of steels, which are primarily used in the production of mechanical components, industrial parts, and construction elements, as well as other accessories related to them.
Tubing Data 3 TUBING DATA Table 1Fractional Carbon Steel Tubing Allowable working pressures are calculated from an S value of 15 700 psi (108 MPa) for ASTM A179 tubing at 20 to 100°F (28 to 37°C), as listed in ASME B31.3. Ultra 654 SMO EN 1.4652, ASTM UNS S32654 stainless steel General characteristics. 7% Mo, very high N alloyed austenitic grade. The most corrosion resistant stainless steel in the world. High mechanical strength. Useful for e.g. pressurized and erosive systems handling chlorinated sea water at higher temperatures, plate
Chemical composition % of steel X4CrNiMo16-5-1 (1.4418):EN 10088-2-2005. Tighter carbon ranges may be agreed at the time of enquery and order. Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0.015 % to 0.030% is recommended and permitted.X4CrNiMo 16-5-1 Steel, Datasheet, Properties, Cross X4CrNiMo 16-5-1 Alloy Steel and Mechanical Properties, Chemical Element, Cross Reference, Datasheet. Datasheet for:Steel Grades:Alloy Steel:X4CrNiMo 16-5-1 Category